General civil Engg. 501 To 600

1. Flooring measurement are taken on the basis of

2. Heavy floods cause

3. Queen post trusses are used when then span is

4. The unit of measurement of expansion joint

5. The removal time of Form work depends on

6. Mat Foundation is also known as

7. Form work of propose to slab spanning up to 4.5 M can be removate after

8. The functions of foundation are

9. Minimum depth of foundation is

10. Differential settlement is due to

11. Failure of foundation is observed because of

12. Village Foundation is to be provided when

13. Combined footing is provided in case of

14. Depth of excavation in case of grillage Foundation is limited to

15. Raft Foundation is provided when

16. Pile Foundation is preferred when

17. Most commonly used building stone in Maharashtra is

18. Missionary may be broadly classified into categories are

19. Rubber Masonry is classified into

20. When the bricks are laid with their length parallel to the face or front direction of the wall the course is known as

21. Water absorption of of good burnt clay bricks should be

22. The process of taking out stones of various sizes from natural rocks is known as

23. The horizontal distance between the vertical joints in successive courses in termed as

24. If the load coming on to pile is transferred to a suitable bearing stratum at its bottom end them it's called

25. The exterior corner of wall is known as

26. The tools used by the masons to check the vertically of wall is

27. Stretcher bond is possible only in

28. When two walls separated by small gap are connected Together by pins it is called

29. Expansion joints in masonry walls are provided if length of wall exceeds

30. When first class bricks are immersed in water for 1 hour the weight of water absorbed by them should not exceed

31. The bond in which each course consists of alternate stretchers & headers is known as

32. Sand used for manufacturing of concrete blocks should pass through

33. Cavity walls is wall comprising of

34. For wall, beams, columns, sides the form can be removed within

35. Forms are the

36. Suitable temperature range of water for curing is

37. Which of the following joints are provided in concrete structures ?

38. Functional requirement of good flooring

39. Basement floor is nothing but

40. Functional requirement of good flooring

41. Which of the following are commonly used roof covering ?

42. Berlin's are provided

43. An open able barrier to enter to into volumetric space of a room is known as

44. Location and number of Doors follows the following guidelines

45. The area of the window ranges between

46. The biggest disadvantage of bricks flooring is that

47. The number of vertical post is in a queen posts truss is

48. The material commonly used to cover the pitched roof with steel trusses is

49. Average weight of Mangalore tiles should be between

50. The unsupported overhang of AC sheet should not be

51. Proposes served by a window are

52. Width of lintel is generally

53. In modern time RCC lintels are extensively used because

54. The horizontal distance measured perpendicular to the front and back faces of Arch is known as

55. The contraction joints in structure are installed to allow for

56. Louvered window is also known as

57. In case of formed and panelled door the ration of glazed to Panelled portion is

58. Normally opted cross- section of style for the shutter is

59. The combination of king post truss and queen post truss is used when the span is

60. Timber and Plywood are the most commonly used materials for form work

61. Which of the following materials required for stone masonry

62. Single stone passing from front to back face & acts as a bond is known as

63. Form work of props to slaps spanning more than 4.5 M can be removed after

64. What type of flooring will you suggest for WC or bathroom

65. Flooring in the bathroom and kitchens of posh residential building is

66. A truss is called composile truss when

67. A.C sheets are laid from right to left starting at

68. Lean to roof is provided when Span limited to

69. James represent the......... side of vertical member of the frame

70. To provide additional M.S. flats that remain embedded in masonry is known as

71. The outer vertical & horizontal members of shutter are termed as

72. Area enclosed between styles & rails and made up of glass or Timber is

73. Mixture of.......... is known as Putty, used for mixing glass panels

74. Rising butt hinge is used for the following purpose

75. Parliamentary hinge provides rotation through

76. Norfold or thumb latch offers........ to the doors

77. Light admittance only is achieved through

78. Lowered Windows are responsible for

79. Sliding doors occupied space with.......... at the top and bottom

80. In case of Buildings where predominate pedestrian traffic is

81. For Counter balancing the door......... are enclosed in the drum

82. Plastic doors are preferred for bath & WC as they are right

83. Usual Locations of sliding windows are in case of

84. Pointed arch in also known as

85. The sides of the abutments or piers below the springers lines is called as

86. Lintel is horizontal structure member which is fixed

87. As a rule the depth of lintel can be adopted as

88. The usual concrete mix for RCC lintel is

89. Ine RCC lintel minimum no. of reinforcement bar should be

90. The lintel formed by using frog bricks is termed as

91. Rubbing end of shutter of revolving doors prevent

92. Threshold provided at the

93. The racess made to receive the shutter is called as

94. Spring hinge provides....... to door

95. The vertical members used to sub divide the shutter is termed as

96. For the areas subject to vermine attack or dampness the material used for frame

97. The minimum width of lock and bottom rail is....... mm

98. Lintails are usually

99. The best curing method for concrete is

100. The roof which slope in all the four direction is